500W DC12V-36 15A Brushless Motor PWM Controller Balanced Auto Hall Driver Board

Description

Home
Category 1
Category 2
About Us
Categories
500W DC12V-36 15A Brushless Motor PWM Controller Balanced Auto Hall Driver Board
DC Brushless Motor Controller
Features:
Drive plate type: JYQD_V6.3E1
Voltage range: 12V-36V
Peak current: 20A
Drive power: ≤ 500W (related working voltage)
Size: 63x43x17mm
Speed control function: voltage speed regulation or single chip
microcomputer control PWM speed regulation
Control terminal connection:
1. GND
2. VR speed control port connection method can be controlled by voltage regulation control or PWM control speed voltage regulation can be adjusted by the adjustable resistance (20K 3 pin bit VR port side of the port side of the 5V port to connect to the GND port through the regulation of voltage control)
3. ZF positive reverse port connection method to connect 5V a direction to the direction of GND
4. Singnal speed pulse output port output of a circle of pulse = motor pole number x 3
5. 5V control terminal 5V voltage output port
Power end connection:
1. VCC power positive input port (12V-36V)
2. GND power input port
3. MC brushless DC motor without a sense / no Holzer motor three line W
4. MB brushless DC motor without a sense / no Holzer motor three line V
5. MA brushless DC motor without a sense / no Holzer motor three line U
Package Included:
1 x 500W DC 12V-36V Brushless Motor PWM Control Controller Balanced BLDC Driver Board
DC Brushless Motor Controller Hall Driver
Compared with the previous version:
1. E2 Effectively prevent damage to the power control board problem-
second E2 optimized power control circuit, improved motor torque output
3. E2 Increases the safety distance of the power leads, makes the surgery of the wire easier and Eliminates the short circuit Caused by the safety distance of the previous version
4. E2 fixed screw hole made a fully shielded design to solve the problem-of shortcircuit Caused by the previous version of the fight to screw
5 E2 in the application of the continuation of all the features of the previous version, can use E2 instead of E1 version
Specification:
operating voltage: 12V-36V
operating Current: <= 15A
Driver Power: <= 500W
Speed ​​Voltage: 0.1V-5V
Operating Temperature: -40-85 ° C
Humidity: 90% RH
Stable protection: Yes
Enable Control: Yes
Over-current protection: Yes
Steering control: Yes
Speed ​​control signal: Yes
Size: 63 * 42 * 17mm (L * W * H); Sample size 3mm,
length: fixing hole center distance 57mm;
width: fixed hole center distance 36.5mm
Power terminal Out:
VCC (positive power supply)
GND (negative one)
MC (motor phases W)
MB (motor phases V)
MA (motor phase U)
Set for the control side:
[GND] control terminal ground
[VR] the governor end 0-5V (corresponding to 10% of motor speed -100%)
[ZF] reversing control (connected to 5V or ground can charge the motor rotation direction)
[M] tachometer pulse output(depending on the number of motor poles corresponding to the number of pulse per revolution of the output number)
[EL] enable control terminal(connected to 5V ot ground running then 5V, grounding the motor stops)
[5V] 5V control terminal
HALL for the hall terminals:
[5V] Hall power positive
[Ha] Hall signal
[Hb] Hall signal
[Hc] Hall Signal
[GND] Hall negative
Wiring:
Control terminal for SET:
1. The motor speed control wiring methods: available potentiometer system speed can also be connected to the MCU control, when the potentiometer control wiring, the potentiometer middle pin is connected to VR speed port, potentiometer connected to both ends of 5V and GND terminal voltage more high speed faster.
2. Motor steering control wiring methods： you can switch control can also be connected to the MCU control, to GND in one direction, then in one direction 5V.
3. Pulse speed signal: high and low output . IC can not understand the information with the customer request.
Hall signal inputs for hall:
Wiring diagram is shown, one corresponding to the HA, HB,HC and on the motor, 5V power supply connected to the motor hal signals positive, GND power supply negative signal to the motor hall.
Note: Due to different motor manufacturers to make the hall of hall line order does not necessarily follow the line on the board to match the sequence, need to be adjusted, please parents who pay attention! If the line sequence wrong, does not boot properly, current, or start other phenomena not open, forced to use the drive plate will burn!!!
Motor driver board 12-36V DC power input , VCC positive power supply,GND power supply is negative.
Electrical wiring methods: Brushless DC motor for the three lines, corresponding MA/U,MB/V,MC/W
Tips: If you use less than 60W, without additional heat sink , be sure to add more than 60W
heatsink fins drive efficiency without lowering the temperature is too high will shine into permanent damage! The size of the heat sink may be a bad environment based work(recommended cooling surface area greater than 200 square centimeters)!When installing the heat sink ,must pay attention to the back of the module 6 MOS pipe insulation, no insulation, it will be adhered to drive plate permanently damaged! Proposes to add insulation films, both sides of the insulating sheet plus thermal grease!
Package Includes:
1 x 12-36V 500W Brushless Motor Controler
Shipping
Payment
Return Policy
Shipping
1,We will arrange shipping for you within 24 Hours after payment cleared except the holidays.
2,We only ship to the confirmed address provided by PayPal. Before you pay, please make sure your address in PayPal matches the address you would like us to ship to. If not, please let us know before we sent you the package, or we will not be responsible for any loss. hope you could understand.
3,we will ship out the order in 1-2 business days after payment cleared .Since it is international shipping ,delivery time is about 15--28 business days to arrive to most countries.
4,We ship items to Worldwide. Thank you!
Payment
We accept PayPal payment ONLY.
If
you  do not have Paypal account, please registered with (http://www.paypal.com)  Payment must be received within 5 days after auctions ended. Please do not  bid if you are not intending to buy. Unpaid dispute will be filed to ebay  for the non payable bidders.
Return Policy
We  are not responsible for custom duty or import  tax.
We will leave POSITIVE FEEDBACK  after receiving the payment. Please contact us if  your are  not satisfied with the item after receive  it.
We could offer  refund,  and refund request is available only requests  within  a week after parcel received & returning the  item as  the same condition as received.
We offer 100% refund if the item is broken before  arrival
,  all you need to do is sending us the clear  pictures  to show it is broken. Defective situation must be  noticed within 7 days after delivery.
All emails will be answered within  1  business day. If you do not receive our reply,  please kindly re-sent your email,and we will reply  to you as soon as possible.
All items sold by us  are being described to the best of our abilities, as  accurate as possible, and with utmost  conscientiousness on our part.However, to avoid any  potential oversights, I respectfully request your  assistance in helping us to make this a mutually  satisfactory transaction by Thoroughly reviewing  item description and photos, and asking all  questions Prior To Bidding.
Please Note that size  and color representation are subject to  manufacturing variance and may not be exact. Also  note that monitor settings may vary from computer to  computer and may distort actual colors. Please read  these terms thoroughly before placing your bid.